Cranberry RED CN-2050 High Power Indoor

Overview

The RED Access Point is a Single Band 802.11n Wireless Access Point is the basic building block of a Wireless LAN infrastructure. It provides connectivity between Ethernet wired networks and radio-equipped Wireless notebook systems, desktop systems, print servers, and other devices.

The RED provides Wireless connectivity to multiple Wireless network devices within a fixed range or area of coverage. The RED Single Band 802.11n Wire- less Access Point is built for the Cloud. The RED comes with the Cloudberry Management portal, which provides remote Management and auto-access point discovery in a single user interface. As a mobile computing device moves out of the range of one access point, it moves into the range of another. As a result, Wireless clients can freely roam from one Access Point to another and still maintain seamless connection to the network.

The RED is extremely simple to set up and can be managed via an intuitive Cloud GUI, CLI, or SNMP. The access point supports IEEE 802.3af Power-over-Ethernet (PoE) and ceiling/wall mount installation.


Point-to-Point
23


Point-to-Multipoint
456

2.4Ghz Band Operational Frequency

Multiple Operating Modes

Wireless Access Point

Point-to-Point Bridge

Point-to-Multi-Point Bridge

The Wireless Access Point operates in the 2.4 GHz frequency band

Operates as a standard 802.11b/g/n access point.

In this mode, the CN-AP-RED only communicates with another bridge-mode wireless access point (with or without clients). Network authentication should be used to protect this communication.

Select this mode only if the CN-AP-RED is the “Master” for a group of bridge-mode wireless access points. The other bridge-mode wireless access points send all traffic to the “Master”, and do not communicate directly with each other. Network Authentication should be used to protect this traffic.

Standards Compliance Access Point complies with the IEEE 802.11b/g/n standards for Wireless LANs.
Full WPA and WPA2 Support WPA and WPA2 enterprise-class strong security with RADIUS and certificate authentication as well as dynamic encryption key generation. WPA-PSK and WPA2-PSK pre shared key authentication without the overhead of RADIUS servers but with all of the strong security of WPA.
Upgradeable Firmware Firmware is stored in a flash memory and can be upgraded easily, using only your Web browser/CLI/SNMP.
Rogue AP Detection The Rogue AP detection feature shows a list of unknown APs to the administrator.
Access Control The Access Control MAC address filtering feature can ensure that only trusted wireless stations can use the CN-AP-RED to gain access to LAN network.
Hidden Mode The SSID is not broadcast, assuring only clients configured with the correct SSID can connect.
Secure Telnet Command Line Interface The secure Telnet command line interface enables easy scripting of configuration of multiple CN-AP-REDs across an extensive network via the Ethernet interface.
Configuration Backup Configuration settings can be backed up to a file and restored.
Autosensing Ethernet Connection Connects to 10/100 Mbps IEEE 802.3 Ethernet networks
LED Indicators Power/Test, LAN speed, LAN activity, and wireless activity are easily identified.
Wireless Multimedia (WMM) Support

Supports WMM QoS (Wireless Multimedia prioritization)

Supports WMM Power Save

Multiple BSSIDs Supports 8 Multiple BSSID. Each BSSID is mapped to a VLAN. When a Access Point is connected to a wired network and a set of wireless stations, it is called a Basic Service Set (BSS). The Basic Service Set Identifier (BSSID) is a unique identifier attached to the header of packets sent over a WLAN that differentiates one WLAN from another when a mobile device tries to connect to the network.
DHCL Server and Client Support DHCP provides a dynamic IP address to PCs and other devices upon request. The CN-AP-RED can act as a client and obtain information from DHCP server; it can also act as a DHCP server and provide network information for wireless clients.
SNMP Support Support for Simple Network Management Protocol (SNMP) Management Information Base (MIB) management. Supports MIB I, MIB II, 802.11 MIB and Proprietary Configuration MIB.
802.1Q VLAN (Virtual LAN) Support A network of computers that behave as if they are connected to the same network even though they actually may be physically located on different segments of a LAN.
VLANs are configured through software rather than hardware, which makes them extremely flexible. VLANs are very useful for user/host management, bandwidth allocation and resource optimization.


Software
AP Modes

Access Point mode

Point-to-point mode

Point-to-multipoint mode

Wireless Security

WEP

WPA

WPA2

IEEE 802.1x RADIUS Authentication

EAP TLS

TTLS

PEAP

SSH

MAC Access Control

Rogue AP Detections

VLAN 802.1Q VLAN (Virtual LAN) Support
QoS WMM based QoS support
Bridging 802.11D and Spanning Tree
System Software Upgrade

TFTP upgrade

FTP upgrade

HTTP upgrade

IP Address Management

Static Client

DHCP Client

DHCP server

DNS resolution

SNMP

SNMP v1 and v2c

SNMP v3 users

SNMP v3 groups

SNMP v3 trap targets

SNMP v3 trap filters

SNMP agent

MIB support

802.11b/g MIB

802.11n MIB

Enterprise MIB

Ethernet MIB

Bridge MIB

Network Management GUI, Telnet, SSH, Syslog, CLI and SNMP, and CLOUD MANAGEMENT
Logging

Event Logging

Remote Syslog

Console display and clear

Web display and clear

System Clock

Manual date and time setting

Time zone

Daylight saving

NTP support

System Information

System configuration

Wireless configuration

Wireless client status

Hardware  
Ethernet Support for 10/100/1000 Gigabit Ethernet
Console Access RS232C based console access
Frequency Band 2.4 GHz
Modulation Technology OFDM with BPSK, QPSK, 16 QAM,64 QAM; DBPSK, DQPSK, CCK
Hardware Encryption 64-bits, 128- and 152-bits WEP, AES,TKIP data encryption
Memory 16MB FLASH and 64MB RAM

Supported Data Rates

IEEE 802.11g

IEEE 802.11ng Data Rates for Channel Width=20MHz and Guard Interval=short (400ms)

Data Rates for Channel Width=20MHz and Guard Interval=long (800ms)

Data Rates for Channel Width=40MHz and Guard Interval=long

1, 2, 5.5, 11, 12, 18, 24, 36, 38, 54, & 108 Mbps (Auto-rate capable)

Best = 7.2, 14.4, 21.7, 28.9, 43.3, 57.8, 65, 72.2, 14.44, 28.88, 43.33, 57.77, 86.66, 115.56, 130, & 144.44 Mbps

Best = 15, 30, 45, 60, 90, 120, 135, 150, 30, 60, 90, 120, 180, 240, 270, & 300 Mbps

Best = 13.5, 27, 40.5, 54, 81, 121.5, 135, 27, 54, 81, 162, 216, 243, & 270 Mbps

Power Supply

IEEE PoE (802.3af switch)

Certification/Standards  
FCC ID Coming Soon
Regulatory Certification uL/CuL
IEEE 802.11b/bg/ng
Environmental  
Temperature Operating temperature: 0 to 50° C Storage Temprerature -10 to 60° C
Humidity Operating humidity: 10-90%,non-condensing
Physical  
Dimensions (LxWxH) 150 x 150 x 35 mm
Weight 0.43 kg (0.94lb)
Ordering Information  
Part No. CN-AP-RED-1005
Description 0.43 kg (0.94lb)